AVR220 harman/kardon
Remote Control Functions
DVD or LD player, depending on how thez Disc Skip Button: This button has no33 for information on programming the remote
remote has been programmed.direct function for the AVR 220, but is oftenwith codes for other devices.)
used when the remote is programmed to oper-
s Tuner Mode: Press this button when the
ate a CD or DVD changer to change the discs in34Volume Up/Down:Press these buttons to
tuner is in use to select between automatic
the changer. (See page 34 for more informationraise or lower the system volume. See page 35
tuning and manual tuning. When the button ison using the remote with other devices.)for more information on programming the
pressed so that the AUTO Indicator R goesVolume Control Punch-Through capability of the
out, pressing the Tuning Buttons u8 will` Preset Up/Down: When the tuner is remote, which allows you to change the AVR
move the frequency up or down in single-step
in use, press these buttons to scroll through the 220Os volume while the remote is set to control
increments. When the FM band is in use, press-another device.
stations programmed into the AVR 220Os mem-
ing this button when a stationOs signal is weak
ory. When some source devices, such as CD
will change to monaural reception. (See page35
players, VCRs and cassette decks, are selectedTV/Video Selector: This button does not
28 for more information.)have a direct function on the AVR 220, but
using the device Input Selectors e, these
buttons may function as Chapter Step or Trackwhen used with a compatibly programmed
t Direct Button: Press this button when
Advance.VCR, DVD or satellite receiver that has a
the tuner is in use to start the sequence for
OTV/Video� function, pressing this button will
direct entry of a stationOs frequency. After press-
28Clear Button:Press this button to clearswitch between the output of the player or
ing the button simply press the proper
incorrect entries when using the remote to receiver and the external video input to that
Numeric Keys r to select a station. (See
directly enter a radio stationOs frequency.player. Consult the ownerOs manual for your
page 28 for more information on the tuner.)
specific player or receiver for the details of how
29Memory Button:Press this button toit implements this function.
u Tuning Up/Down: When the tuner is in
enter a radio station into the AVR 220Os preset
use, these buttons will tune up or down through
memory. Once the MEMORY Indicator O36SPLButton:This button activates the AVR
the selected frequency band. If the Tuner Mode
flashes, you have five seconds to enter a preset220Os EzSet function to quickly and accurately
Button s@ has been pressed so that the
memory location using the Numeric Keyscalibrate the AVR 220Os output levels. Press and
AUTO Indicator R is illuminated, pressing and
r. (See page 29 for more information.)hold the button for three seconds and then
holding either of the buttons for three seconds
release it. Note that the Test Tone will begin cir-
will cause the tuner to seek the next station with
acceptable signal strength for quality reception.30Delay/Prev Ch.:Press this button toculating, and the Program/SPL Indicator c
When the AUTO Indicator R is NOT illumi-begin the process for setting the delay timeswill change colors. During this sequence, EzSet
used by the AVR 220 when processing surroundwill automatically adjust the output levels for
nated, pressing these buttons will tune stations
sound. After pressing this button, the delayall channels until they have equal output levels,
in single-step increments. (See page 28 for more
times are entered by pressing the Set Buttonas shown by the Program/SPL Indicator c
information.)
o and then using the D/¤ Buttons mqlighting green for each channel. Press this but-
v OSD Button: Press this button to activateto change the setting. Press the Set Buttonton again when the adjustment is complete to
the On Screen Display (OSD) system used to seto again to complete the process. (See pageturn off the test tone. (See page 21 for more
up or adjust the AVR 220Os parameters.18 for more information.)information on EzSet.)
w Macro Buttons: Press these buttons 31:Button:Press this button to change a376-Channel Direct Input:Press this but-
to store or recall a OMacro�, which is a setting or selection when configuring many of theton to select the component connected to the
preprogrammed sequence of commands AVR 220Os settings.6-Channel Direct Input a as the source.
stored in the remote. (See page 34 for more
information on storing and recalling macros.)32Speaker Select:Press this button 38Mute:Press this button to momentarily
to begin the process of configuring the silence the AVR 220 or TV set being controlled,
x Transport Controls: These buttons do
AVR 220Os bass management system for usedepending on which device has been selected.
not have any functions for the AVR 220, but
with the type of speakers used in your system.
they may be programmed for the forward/
Once the button has been pressed, use theWhen the AVR 220 remote is being programmed
reverse play operation of a wide variety of CD
D/¤Buttonsmqto select the channelto operate another device, this button is pressed
or DVD players, and audio or video cassette
you wish to set up. Press the Set Button owith the Input Selector Button e to begin
recorders. (See page 35 for more information
and then select another channel to configure.the programming process. (See page 33 for
on programming the Transport Control Punch-
When all adjustments have been completed,more information on programming the remote.)
Through capability of the remote.)
press the Set Button o twice to exit the
39EzSetSensor Microphone:The sensor
settings and return to normal operation. (See
y Skip Up/Down Button: This button has a
microphone for the EzSet microphone is behind
page 19 for more information.)
direct function with the AVR 220, but when
these slots. When using the remote to calibrate
used with a compatibly programmed CD or
speaker output levels using EzSet, be sure that
33Spare Button:This button does not have
DVD changer they will change the disc currently
you do not hold the remote in a way that cov-
any function for the operation of the AVR 220,
being played in the changer.
ers these slots. (See page 21 for more informa-
but it is available for use when programmed
tion on using EzSet.)
with the code from another remote. (See page
13 REMOTE CONTROL FUNCTIONS |
ACEC
